ONAIR / Maintenance & Troubleshooting

Keep your air ride ready.

A practical maintenance routine for moisture, leaks, wear and the way your system behaves.

THE ANSWER / START HERE

Keep collected water out, watch for changes in pressure and compressor behaviour, and inspect the parts that move. Your equipment instructions and the conditions you drive in determine the schedule - not a universal maintenance interval.

Updated October 29, 2026 ONAIR Automotive

ONAIR air strut installed inside a wheel well, with red collars and a connected air line.
The details behind the wheel deserve attention too. Inspect only with the vehicle properly supported.
01 / Moisture

Check the tank and traps. One does not replace the other.

02 / Changes

A settling corner or extra compressor cycling needs investigation.

03 / Safety

Never reach beneath a car supported only by air suspension.

01 / THE DETAILS

Start with a baseline, not a guess.

After installation, record your normal driving height, typical controller readings and how the compressor sounds when it replenishes the tank. Ask the installer to show you every drain, fuse and isolation point. Keep the component list and supplied instructions together.

Before a drive

Confirm the car has reached its normal driving height and has clearance. A familiar number on the controller is not a substitute for checking the car.

Arrange inspections around your use: after installation work, before a season change, after wheel or suspension changes, and whenever something behaves differently. Increase moisture checks when humidity or compressor use increases.

02 / THE DETAILS

A water trap is not the whole moisture routine.

The tank can collect condensation even when a water trap is fitted. Check both using the instructions for those exact components. Keep the designated drains accessible instead of burying them behind a permanent beauty panel.

  • Look for collected water and confirm the drain operates as intended.
  • Use the specified drain procedure and required pressure state.
  • Inspect automatic or heated equipment too; it is not maintenance-free.
Do not loosen a pressurized fitting.

Use the designated drain, not an improvised opening. Isolate power and relieve pressure wherever the servicing instructions require it. Do not add oils, solvents or antifreeze without approval for the complete system.

03 / THE DETAILS

Look at the wear points.

With the vehicle safely supported, inspect accessible air springs for rubbing or cuts, air lines for chafing or kinks, and fittings for movement. Check mounting hardware, compressor isolation mounts and electrical connections against the installation instructions.

Pay particular attention after a wheel change or alignment. A line that cleared the original wheel may not clear the new one through steering and suspension travel. For a closer walkthrough, use the air-suspension inspection guide.

04 / THE DETAILS

Know when to stop topping it up.

Use a change as a reason to inspect, not a diagnosis by itself.
What you noticeUseful next step
One corner keeps settlingRecord the conditions and arrange a leak inspection.
The compressor runs much more oftenCheck for pressure loss and air demand. Do not use extra runtime to hide a leak.
New rubbing, heat damage or damaged lineStop normal use and have the cause corrected.
The car cannot hold a safe driving heightDo not drive it. Arrange repair or recovery.

05 / THE DETAILS

Give winter its own plan.

A year-round daily and a summer project need different preparation. Use the Canadian winter maintenance guide for cold-weather driving, or the winter storage guide when putting the car away.

For support, share the symptom, when it happens, the installed management and air-supply equipment, and clear photos. A short record of the change is more useful than repeatedly changing settings.

ONE MORE THING

The questions that come next.

How often should I drain the tank?

Follow the component instructions and check what your own system collects. Humidity, temperature and compressor use change the workload. A fixed interval from someone else's car is not a guarantee for yours.

Does an automatic water trap mean I can forget about moisture?

No. Verify its operation and wiring where applicable, and continue checking the tank and the rest of the system.

Is a lower reading on a cold morning always a leak?

Not necessarily. Compare actual height and readings under similar temperatures and loading. Persistent settling, especially at one corner, still deserves an inspection.

YOUR NEXT STEP / ONAIR

Something changed? Start with the symptom and the equipment fitted.

Get help with a system issue
Sources & equipment references

General education is not a replacement for the instructions supplied with your exact components. Product-specific ratings and procedures do not transfer automatically to another setup.

Back to the answer